ট্রান্সমিশন এন্ড ডিস্ট্রিবিউশন অব ইলেক্ট্রিক্যাল পাওয়ার MCQ
81. A line which connects distributor to substation is called--
service mains
distributor
feeder
infinity
82. the minimum phase -neutral voltage at which corona occurs, is called-
critical disruptive voltage
visual critical voltage
fieash over voltage
none of the above
83. The surge impedance for over head line is taken as-
10-202 Ω
100-200 Ω
50-600 Ω
1000-2000Ω
84. The ring main system is used in power distribution because it--
ব্যাখ্যা: There are less voltage fluctuations at consumer terminals. The system is very reliable as each distributor is fed via two feeders. In the event of fault on any section of the feeder, the continuity of supply is maintained
is reliable for continuity of supply
gives better voltages regulation
results in less feeder losses
all of the above
85. Potential difference to any equal charge is measured in,
ব্যাখ্যা: The unit of potential difference between any two equal charges is volt.
coulomb
Ampere
joule
volt
86. Modern high-voltage lines are designed with a safety factor of about --
1.5
2
3
4
87. The highest point on the daily load curve represents-
average load
load factor
maximum load
none of the above
88. TStability of a system is not affected by-
ব্যাখ্যা: Stability of power system is affected by-
-Reactance of transmission line
-Reactance of generator
-Excitation of generator
-Input output torque.
Reactance of line
Losses
Reactance of generator
Output torque
89. When the load factor of a power station increases, the units (kwh) generated-
are increased
remain the same
are decreased
none of these
90. Which of the following is not the distribution system, normally used-
ব্যাখ্যা 2 AC distribution system can be classified as- -Single phase-2 wire system -Sinele phase-3 wire system -Two phase-3 wire system -Two phase-4 wire system -Three phase-3 wire system -Three phase-4 wire system
3 phase 4 wire
Single phase-3 wire
Single phase -4 wire
3 phase-3 wire
91. For a single circuit 3 phase line the inductance per phase per km is of the order of--
1mH
0.2mH
10 mH
0.1 mH
92. For a distortionless transmission line --
R/L = G/C
RG=LC
RL= GC
RLGC-0
93. At distribution substation voltage is stepped down to-
66kV
132kV
11kV
415/230 Volts
94. Capacitance of a transmission line is the result of-
ব্যাখ্যা: Capacitance of a transmission line is the results due to the potential difference between the conductors. The conductors get charged in the same way as the parallel plates of a capacitor, capacitance between two parallel conductors depends on the size and the spacing between the conductors
Potential diference between the conductors
Current flow in both conductors
Current flow in either conductors
Charge per unit current
95. The most severe unsymmetrical fault is-
ব্যাখ্যা: Symmetrical three phase fault is the most severe kind at the transmission lines, while for faults occurring very close to the generating station or synchronous generator, single line to ground fault is the most severe.
single line-to-ground fault
line-to-line fault
double line-to-ground fault
none of the above
96. The line voltage on the LT side of a distribution transformer is--
ব্যাখ্যাঃA LT (Low Tension) line is a low voltage line and ITT (High Tension) line is a high voltage line. In LT supply is of 400 volt for three-phase connection and 230 volt for single-phase connection. High tensione HT supply is applicable for bulk purchase who need 11 kilo-volt (kV).
400V
230V
11KV
33kV
97. The common fault is overhead distribution system is-
ব্যাখ্যা: About 50-55% fault in overhead distribution system is one phase to earth fault and 12-15% fault is phase in phase fault
phase to phase fault
one phase to earth fault
all phase short circuited
none of the above
98. Corona is affected by-
condition of atmosphere
line voltage
size & spacing of conductor
all of the above
99. In de transmission, the skin effect is-
large
zero
small
depends on voltage
100. The distribution transformer is generally connected in--
ব্যাখ্যা: The distribution transformer is generally connected in deta/star. In secondary side, star connection is required which has neutral point. From this star connection. Voltage is used by consumers.
Delta/Delta
Star/Delta
Star/Star
Delta/Star